Disconnect the coolant pump-to-engine hose and position aside. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley 5, Disconnect the heater hose from the coolant pump. Remove the 3 bolts from the coolant pump assembly. The manual transmission has no fluid surprises. Replace 2003-2008 Toyota Corolla Side Mirror, How to Change Install 2004 2005 2006 About 22,000 results 0. Just got back from the dealer. Posted on May 25, 2010 Apr 10, 2012 - Uploaded by GregHint See how even a novice can repair a passenger mirror on a FordEscape.
Did You Know… The Fusion radio is a programmable module, meaning if it is replaced for a new one, the new one will have to be programmed with a scan tool or the back lighting will not work. Refill the vehicle with clean coolant. If anything like that exist, you need to have it replaced, and also the water pump needs to be replaced at the same time since they can cause premature failure of the timing belt. Your water pump is responsible for pumping water and coolant to your engine, keeping it cool and functioning well. Tape the belt into position where it's half on the large pully. To replace the seat filter, adjust the seat all the way back, push up on the plastic out-ring of the filter and rotate until it unlocks. .
Thanks, Tim Timbo wrote:Thats what I was thinking also. Then crank it to get the belt pulled on. Remove the 3 bolts from the coolant pump assembly. Using tape to hold it in place will keep your fingers safe. To further refine engine character and improve durability, both engines feature deep-skirted engine blocks. It produces 221 hp at 6,250 rpm and 205 ft. Any ideas Well it winter again here in Wisconsin and the Fusion still is not producing heat at idle.
Lower the strap in until the upper mark is at the bottom edge of the filler hole. This similar idea is also used in the newer Escapes, however, in the Escape, these upper rows are the transmission cooler. They are available for the following Ford Fusion years: 2018, 2017, 2016, 2015, 2014, 2013, 2012, 2011, 2010, 2009, 2008, 2007, 2006, 18, 17, 16, 15, 14, 13, 12, 11, 10, 09, 08, 07, 06. I have had my dealer look at it and they actually checked another Fusion to see if the temperature was the same as my car and apparently it was. The base part number on the filter is 6C683.
This was fairly easy to do. If there isn't an inspection plate for the belt, you will need to take off the cover to get a closer look. Inspect the used coolant before putting it back in the vehicle. To enhance efficiency, the Duratec 23 features Charge Motion Control Valves in the intake runners similar to those found in the powerful F-150 pickup to boost torque and improve combustion at low engine speeds. But, at least they gave us a trap door under the rear seat to access the fuel pump for replacement. This belt cannot tolerate lubricants, so do not spray these belts with any kind of lubricant or dressing.
The heat now works better than it ever has, and I now have heat when the car idles. Install the coolant pump belt. Our online parts catalog uses real-time inventory, so you can be assured the parts you buy are in stock at the time of ordering. Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly. This worked for my 2008 for fusion. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley 5. Also the blower seems noisy.
Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley 5, Disconnect the heater hose from the coolant pump. Kind of strange to have a new car that already required a coolant flush. You can read the service bulletin here: I hope this helps anyone with a Fusion that is having this issue. They also said it may take up to 15 minutes for it to warm up but it will never be the same as the front vents as the heated air has to travel farther. Install the coolant pump belt. . Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly.
This part is also sometimes called Ford Fusion Water Pumps. How and why is that? Does anyone have a service guide that discusses this? View of the water pump and related components-3. Then search for a fuse to pull so the car will not start, but will still crank over. Ford Fusion Replacement Water Pump Information Search our online water pump catalog and find the lowest priced discount auto parts on the web. We sell wholesale to the public. The drier is a molded housing down one side of the condenser. The coolant is then fed through the water pump, which supplies the engine block with coolant, allowing it to operate at an efficient temperature.